PEEK Cross Recess Countersunk Screws are polyether ether ketone fasteners specified with a countersunk head and a cross-shaped recessed drive. Flybear supplies this product through a B2B RFQ process rather than fixed online retail specifications. Production requirements are reviewed against customer drawings, physical samples, BOMs, product lists or other confirmed technical documentation. Exact PEEK grade, thread geometry, screw dimensions, dimensional tolerances, surface appearance, color, applicable standards, inspection criteria and packaging requirements remain project-specific and should be confirmed before quotation and production.
PEEK Cross Recess Countersunk Screws Overview
The product is specified in PEEK material with a countersunk head and cross recess drive configuration. PEEK Cross Recess Countersunk Screws can be evaluated for assemblies where the engineering design calls for a polymer fastener with countersunk seating and recessed cross-drive installation. The countersunk head should correspond to the seating geometry of the mating component. Exact head diameter, head angle, recess geometry, nominal thread diameter, pitch and overall screw length are according to drawing. The specific PEEK compound grade, color and surface requirements should also be defined during RFQ when controlled by the customer specification.
Key Features
- PEEK material confirmed for the requested screw configuration; the exact material grade or compound designation is confirmed during RFQ.
- Countersunk head configuration for assemblies designed with a corresponding recessed seating area.
- Cross-shaped recessed drive as specified, without assuming a particular Phillips, Pozidriv or standardized recess designation.
- PEEK Cross Recess Countersunk Screws can be reviewed against customer-defined dimensions, thread requirements and dimensional tolerances.
- Thread form, nominal diameter, pitch and engagement details are according to the approved drawing or confirmed sample.
- Head diameter, countersunk angle and recess dimensions can be specified through customer technical documentation.
- Color and surface appearance are confirmed during RFQ rather than assumed from a generic PEEK screw specification.
- Suitable for B2B sourcing based on drawings, samples, BOMs and project-specific product lists.
Specification Options
| Product Type | PEEK cross recess countersunk screw |
| Material | Polyether ether ketone (PEEK) |
| Material Grade | PEEK; exact grade confirmed during RFQ |
| Head Style | Countersunk head |
| Drive Type | Cross recess |
| Thread | According to drawing |
| Dimensions | According to drawing |
| Surface Finish | Confirmed during RFQ |
| Color | Confirmed during RFQ |
| Standard | Confirmed during RFQ |
| Tolerances | According to drawing |
| Inspection | According to drawing or agreed inspection requirements |
| Packaging | Confirmed during RFQ |
Typical Applications
This screw configuration may be considered for industrial assemblies where the technical specification calls for a PEEK fastener with countersunk seating and a cross recess drive. Typical project areas may include:
- Electrical and electronic equipment designed around specified polymer fasteners
- Instrument housings, panels, covers and mounting components
- Plastic component assemblies incorporating countersunk mounting locations
- Mechanical or electromechanical equipment using drawing-specified non-metallic screws
- Custom industrial assemblies manufactured according to customer drawings or BOM requirements
Final suitability should be verified against the actual assembly design, mechanical load, operating environment, mating material, thread engagement and installation conditions. Any project-specific performance requirement should be stated in the RFQ and reviewed against the confirmed material grade and assembly conditions.
Manufacturing and Quality Support
Customer specifications can be evaluated through our manufacturing capabilities, including drawing-based review of countersunk geometry, drive recess dimensions, thread requirements and other production details. Inspection expectations can be discussed with reference to our quality process, while related industrial fastener families can be found through the Products page. Additional company information is available from Flybear Industrial.
For PEEK Cross Recess Countersunk Screws, technical review can cover the required PEEK designation, screw dimensions, thread specification, head geometry, cross recess requirements, dimensional tolerances, appearance criteria and agreed inspection points. Special material, dimensional, inspection or packaging requirements should be included in the RFQ so manufacturing feasibility can be evaluated before quotation.
What to Include in Your RFQ
- Dimensioned technical drawing with relevant tolerances
- Physical samples or clear sample photos when available
- Required PEEK grade or material specification
- Thread type, nominal diameter, pitch and engagement requirements
- Head diameter, countersunk angle, recess dimensions and overall screw length
- Required surface appearance, finish and color
- Order quantity or estimated annual demand
- Inspection criteria, reports or documentation requirements
- Packaging and labeling requirements
- Delivery destination and other project-specific information
Frequently Asked Questions
Can these PEEK screws be customized?
Yes. Thread dimensions, overall length, countersunk head geometry, cross recess dimensions, color and other project-specific requirements can be evaluated according to customer drawings or samples. Final manufacturing feasibility is subject to technical review.
What information should I provide for quotation?
A dimensioned drawing is preferred. Physical samples, BOMs, product lists or clear photos can also support the initial review. Please include material grade, thread details, dimensions, quantity, inspection requirements and delivery destination when available.
Why is there no fixed online price?
Industrial fastener pricing depends on the confirmed material grade, dimensions, tooling requirements, tolerances, order quantity, inspection level and packaging. A project-specific quotation is therefore prepared after the technical requirements have been reviewed.
Can the PEEK grade, countersunk head or cross recess geometry be specified?
Yes. The required PEEK grade, head diameter, countersunk angle and recess geometry can be defined by customer drawing or purchasing specification. Exact dimensions, material requirements and manufacturing feasibility are confirmed during RFQ.
Send your drawing, sample photos or product list through our contact page for technical review and quotation.
